Choose a car/bike key
brand
model
year

Chip Lada Granta, Priora, Kalina | 2004-2022 | working key (black key) | Original

ORIGINAL
Reviews:
(0)
  • Brand: NXP
  • Product Code: TRN-3610
  • Reward Points: 8
  • Availability: 10
Price:
841 ₽
Found cheaper?
Total:
841 ₽
Price in reward points: 841
заказать в WhatsApp
  • Product overview
  • Details and instructions
  • Reviews (0)
  • Questions (0)

Chip for cars VAZ, Lada Granta, Priora, Kalina, Chevrolet Niva (Lada Granta, Priora, Kalina, Chevrolet Niva) is used for a working key BLACK KEY, is programmed only if the car owner has a training RED KEY

Details and instructions

BLACK KEY, is programmed only if the car owner has a training RED KEY as follows

1. Close all vehicle doors. Turn on the ignition with the learning key and wait at least 6 seconds.
2. Turn off the ignition. The lamp should flash rapidly (5 times per second) as long as the learning procedure is being performed correctly. If the lamp stops flashing quickly, it indicates an incorrect operation, out of time, or a malfunction. Remove the learning key from the ignition.
3. While the lamp is flashing (about 6 seconds), insert the working key into the lock and turn on the ignition. If everything is done correctly, the buzzer will emit three beeps when the ignition is turned on.
4. Wait with the ignition on (about 6 seconds) until the buzzer emits two more beeps. If after 6 seconds the buzzer did not sound, and the quick flashing of the light stopped, then turn off the ignition and start the procedure again. If the situation repeats, then this means a malfunction or that this working key has already been trained with another immobilizer.
5. Turn off the ignition.
6. If it is necessary to learn the second working key, then repeat steps 3-5, using the second learning working key to turn on the ignition. If not, continue execution from point 7.
7. While the lamp is flashing (about 6 seconds), it is necessary to remove the key from the ignition lock, insert the learning key into the lock again and turn on the ignition. If everything is done correctly, the buzzer will emit three beeps when the ignition is turned on.
8. Wait with the ignition on (about 6 seconds) until the buzzer emits two more beeps.
9. Turn off the ignition. Do not remove the learning key from the ignition. Approximately 6 seconds after the ignition is turned off, the buzzer should emit a single beep and the lamp should start flashing twice as fast. If the buzzer did not sound, and the quick flashing of the light stopped, then turn off the ignition and start the procedure again. If the situation repeats, then this means a malfunction or that this learning key does not fit this controller.
10. Not later than 6 seconds after the sound signal (while the lamp is flashing quickly), you must turn on the ignition with the same learning key. After waiting 2-3 seconds, turn off the ignition. Not later than 5 seconds after turning off the ignition, the buzzer should give three beeps, and the light should stop flashing quickly. Do not turn on the ignition for at least another 10 seconds. When working with some controllers, the light bulb stops flashing and the buzzer emits 3 beeps already when the ignition is turned on. In this case, you should still turn off the ignition and wait at least 10 seconds. At the end of the learning procedure, it may be necessary to synchronize the immobilizer and controller codes. This means that after the end of the learning procedure, the controller will not allow the engine to be started when the ignition is turned on for the first time. To perform synchronization, you must turn on the ignition with any trained key (preferably a working one). Wait 6 seconds. If the immobilizer lamp began to show an error condition (blinks 1 time per second), then turn off the ignition and wait at least 10 seconds. Then turn on the ignition again. The lamp should not flash, and the engine should start. If 3 seconds after the ignition is turned on, the lamp lights up with a constant light, this means that the controller has not activated the anti-theft function and the learning procedure should be repeated again.

Reviews (0)
Register, leave product reviews, earn bonuses!

There are no reviews for this product.

Questions (0)

Question about a product? Problem with your purchase? Something does not work? Fill out the feedback form and we will contact you and help!

Specials
Latest